Pickup & Delivery Available SCHEDULE

What Rinse Hold Actually Does and When an Extra Rinse Helps

Two buttons on the same panel get used almost interchangeably, and they do completely unrelated jobs. One of them stops the machine with the drum full of water. The other adds a whole extra fill and drain to the end of the cycle. People reach for whichever one they half remember when a load comes out feeling slightly off, and about half the time they pick the one that cannot possibly address the problem in front of them. Both settings are genuinely useful. Knowing which question each one answers saves a lot of guessing.

Rinse hold and extra rinse options on a washer control panel

What Rinsing Is Actually Doing

A rinse is not a cleaning step. By the time the wash water drains, the surfactant has already done its work, and what is left in the cloth is a quantity of dissolved material that nobody wants there: detergent, loosened soil, dissolved mineral and whatever came off the fabric. Rinsing is pure dilution, and it follows arithmetic that is worth having in your head.

A spun load still holds a fair amount of water inside the yarn, and that retained water carries the full concentration of the bath it came from. The rinse adds clean water to it. The concentration that results is set by the ratio of retained water to added water, and nothing else. Agitation during a rinse does almost nothing except help the exchange happen faster.

Because each rinse multiplies rather than subtracts, the returns fall off steeply. The first rinse removes the great bulk of what was dissolved. The second removes most of what the first left, which is a much smaller number to begin with. By the third you are chasing a remainder that is already too small to feel or smell in most fabrics.

That shape explains almost everything about these two settings. An additional rinse is a real improvement over one rinse and a marginal one over two. And no number of rinses touches anything that is not dissolved in the first place, which turns out to be the most common disappointment of all.

What the Hold Setting Is For

Rinse hold stops the machine after the final rinse has filled, with the load submerged and the drain and the final spin still waiting. The purpose is narrow and mechanical. Cloth left crushed against a drum wall after a high speed spin sets creases, because the fibers are compressed, damp and warm, and that is precisely the condition in which cellulose takes a new shape and keeps it.

Cotton fibers hold their form through hydrogen bonds between cellulose chains. Water gets in between those chains and lets them slide, which is why damp cotton is easy to deform. As it dries in a folded position, the bonds reform in the new arrangement and the fold becomes the fabric’s memory. That is what ironing does deliberately and what a spun load sitting in a drum does accidentally.

A load floating in water cannot do that. Nothing is compressed, nothing is under its own weight, and the cloth is uniformly wet rather than drying in creases. So the setting exists for the case where you will not be in the room when the cycle ends, and the alternative is a shirt that comes out with a hard fold across the chest.

It has a second use that the name does not suggest. Stopping the machine with the drum full is also a soak, and a load held in plain rinse water for a while will loosen some residual soil by simple diffusion. That is a side benefit rather than the point, and it is the half of the setting that gets overused.

What the Extra Rinse Is For

The extra rinse earns its place in machines that use very little water. A low water machine achieves its cleaning with a concentrated bath and a lot of mechanical movement, which works well, but concentrated means that the water retained in the cloth at the end of the wash is carrying more dissolved material than it would in an older machine. One rinse against that is thin.

Dense fabric makes the same argument. A bath towel, a pair of heavy jeans or a quilted mattress pad holds a great deal of water in its interior, and water held deep in a thick yarn exchanges slowly with the water around it. A single rinse often ends before the inside of the yarn has equilibrated with the clean water outside it.

Hard water is the third case. Calcium and magnesium react with some surfactant types to form compounds that are much less soluble than the surfactant was, and those sit in the cloth rather than rinsing out. More water carries away more of them. It is also why a load washed in hard water feels different from the same load washed in soft.

And then there is dosing, which is the real reason most people turn it on. If a cap has been filled rather than measured, there is simply more surfactant in the cloth at the end of the wash, and an extra dilution step is doing cleanup after the fact. It works. It is still treating a symptom.

When Neither Setting Helps

Nothing dissolved means nothing to dilute. A film of fabric softener on a towel is not in solution, it is deposited on the fiber and bound there by charge. A polymer residue from a spray, a silicone from a hair product and an oily soil that never emulsified are all in the same category. Adding rinses to any of them accomplishes nothing at all.

An overpacked drum defeats both settings. Rinse water has to physically exchange with the water inside the cloth, and that requires the load to move and open. A drum filled to the top slides as a solid mass, the center never meets clean water, and you can run three rinses and leave the middle of the load exactly as it was.

A long hold has costs of its own. Loose dye that came off one garment during the wash stays in suspension in the rinse water, and a load left floating in it for hours gives that dye time to find the pale items. Elastic, wool and anything with a water repellent finish also do better out of prolonged immersion than in it.

There is a smell question too. Water standing in a closed drum goes flat, and cloth left in it long enough picks up that flatness, which then takes another wash to shift. The setting is for an hour or two of insurance against creasing, not for leaving a load overnight.

Choosing Between the Two

The test is what the complaint is. If the load comes out creased, stiff with fold lines, or wrinkled in a pattern that matches the shape of the drum, that is a mechanical problem and rinse hold is the setting that addresses it. If it comes out feeling slick, faintly soapy, or harsher than it should, that is a residue problem and the extra rinse is the one.

If the complaint is a smell, neither is likely to be the answer, and both can make it worse. Smell usually traces back to dose, to water temperature or to a load that never got enough room to move. Those are things to change in the wash itself rather than at the end of it.

There is also a sensible default, which is to measure the detergent for the real size of the load and then not need the extra rinse most of the time. Every additional fill is more water and more tumbling against the fabric, and mechanical action is what wears cloth out. Using the setting for towels and heavy items and leaving it off for shirts is a reasonable compromise.

For the hold, the useful habit is to treat it as a short term parking place. Turn it on when you know the cycle will finish while you are out of the house, and finish the spin when you get back rather than hours later. Used that way it is one of the few settings that genuinely saves work later.

Cold Water Rinses in Fargo

Water arriving in a Fargo household in the depths of the cold season comes in close to freezing, and that changes the rinse more than people realize. Surfactants and the compounds they form with dissolved mineral are both less soluble in very cold water, so the same quantity of residual material is harder to carry away than it would be in summer.

That is the strongest argument for the extra rinse here, and it is a seasonal argument rather than a permanent one. A load of towels washed in the coldest part of the year genuinely benefits from a second dilution in a way that the same towels in warm weather would not. The same goes for anything thick enough to hold water deep inside its yarn.

The other local note is about creasing. Laundry rooms get cold in winter, and cold damp cotton compressed in a drum takes a set just as readily as warm damp cotton does, only slower. A load left spun and sitting in a cold room all evening comes out with folds that an ordinary dryer cycle will not fully release.

Room for the Water to Work

Both of these settings assume the load can move. The single biggest improvement most people can make to a rinse has nothing to do with the number of rinses and everything to do with giving the cloth enough space in the drum that clean water can actually reach the inside of a thick yarn.

The machines at our self-service laundry on 45th Street South give towels, jeans and quilts the water volume and the room to tumble that makes a single rinse do what three rinses do in a crowded drum, and you can run heavy items and light ones side by side instead of in sequence.

Our machines and the store are cleaned daily.

Our wash-dry-fold service covers the everyday laundry.

For general guidance, The American Cleaning Institute publishes a laundry basics guide that is a useful cross-check.

The short version

Rinsing is dilution, so the first one does most of the work and each one after it does less. The hold setting leaves a load floating instead of spun and creased against the drum, which is a mechanical fix for fold lines. An extra rinse lowers whatever is still dissolved in the cloth, which helps with dense fabric, hard water and a heavy dose. Neither one touches a residue that is bound to the fiber rather than dissolved.

WaveMAX Fargo is at 2551 45th St S Suite 147, easy to reach from Fargo and the surrounding area. If you have a load that will not fit at home, call us at 701-707-0621.